Close

Nitrate Nitrogen (7C2)

Initially, milled air-dry soil is extracted for 1 h with 2M KCl at a 1:10 soil/solution ratio. For 7C1a to 7C1h methods, mineral-N components are quantified by steam distillations and subsequent titrations. For 7C2 methods, mineral-N fractions in the clarified soil extract are determined by automated colorimetric procedures. Ammonium ions (NH4+) are measured by a modified Berthelot indophenol reaction, while the Griess-Ilosvay reaction is used for NO3-N (and NO2-N). The methods specify reporting results for NH4-N and NO3-N [plus NO2-N if present], respectively, as mg N/kg on an oven-dry (105oC) basis. Specifically, method 7C2a relates to an automated colour, continuous segmented flow analytical finish, while Method 7C2b codes an automated colour finish by flow injection analysis. Little difference is expected in results due to choice of colorimetric finish.

Close

Electrical conductivity (EC) of 1:5 soil/water extract (3A1)

This test on milled air-dry sample at a soil/water ratio of 1:5 for 1 h is suitable for use on all soils, irrespective of whether acidic or alkaline. It usually underestimates the soluble salt status of soils containing natural or added gypsum, particularly if ³ 1% of gypsum is present. Such soils would have an EC of about 2 dS/m. Soil EC x 0.336 (Method 3B1) approximates percent total soluble salts, while approximate soil ionic strength (Method 3C1) at 0.1 bar (I0.1) can be calculated as follows: I0.1 = [0.0446*EC1:5 – 0.000173], where I0.1 has units of mM, and EC1:5 has units of dS/m @ 25oC.

Close

Exchangeable Bases - Ammonium Acetate (15D3)

 

Exchangeable bases - 1M ammonium acetate at pH 7.0.

 

This rapid method for exchangeable cations in non-saline acidic through to slightly alkaline soils has no pre-treatment for soluble salts. It should yield similar data to those of method 15A1, except it can overestimate exchangeable Ca in soils containing calcium carbonate.

Close

Exchangeable Bases - Ammonium Chloride (15A1)

Method for measuring exchangeable bases (Ca2+, Mg2+, Na+, K+) - 1M ammonium chloride at pH 7.0

 

Suited for use on all soils, irrespective of whether acidic or alkaline, but preferred on acidic to weakly alkaline soils not dominated by solid-phase carbonates. Method 15A1 has no pre-treatment to remove soluble salts, with alternatives to remove them chemically (15A2) or to adjust for the presence of soluble sodium (15A3).

Close

Mehlich3 ICP (18F1)

Analysis of Mehlich 3 extract using inductively-coupled atomic emission spectroscopy (ICP-AES)

Close

Extractable Phosphorus - Olsen (9C2)

This extractable P test on milled air-dry sample uses freshly prepared 0.5M sodium bicarbonate @ pH 8.5 as the extractant. The soil/extractant ratio of 1:20 and a relatively short extraction time of 30 min favours readily available forms of soil P, while suppressing the solubility of basic calcium phosphates often found in neutral and alkaline soils. Method 9C1 involves a manual, molybdenum-blue colorimetric finish with a preferred absorbance at 882 nm. Method 9C2a defines an equivalent automated molybdenum-blue continuous segmented flow analytical finish, while Method 9C2b codes an automated colour finish by flow injection analysis. No significant difference is expected in results due to the analytical finishes described. The methods specify reporting results as mg P/kg on an air-dry basis.
Close

pH: 1:5 SOIL:0.01M CaCL2 Suspension (4B2)

This pH test on milled air-dry sample is suitable for use on all soils, irrespective of whether acidic or alkaline. Values are usually unaffected by fertilisation prior to sampling, as changes to the soil’s ionic strength is masked by the calcium chloride. Code 4B1 indicates direct use of 0.01M CaCl2, at a soil/solution ratio of 1:5, with mechanical shaking for 1 h prior to pH measurement using calibrated electrodes positioned in the unstirred supernatant after settling of the suspension. Code 4B2 provides a similar measurement outcome but relies on the addition of 0.21M CaCl2 to a 1:5 soil/water suspension to achieve 0.01M CaCl2 prior to measurement of pH as for 4B1.

Codes 4B3 and 4B4 are identical to 4B1 and 4B2, respectively, except the soil/CaCl2 suspensions are stirred during measurement. Method 4B5 codes for an MIR surrogate measurement. There is merit in separate use of both water and calcium chloride to measure soil pH.

Close

pH of 1:5 soil/water suspension (4A1)

This test on milled air-dry sample involves mechanical shaking with deionised water in a closed system for 1 h at a soil/water ratio of 1:5 prior to pH measurement using calibrated electrodes, while stirring the soil/water suspension. The method is suitable for use on all soils, irrespective of whether acidic or alkaline. Values may be lower than expected on recently fertilised soils due to a temporary increase in soil solution ionic strength.
Close

Total organic carbon - high frequency induction furnace, volumetric (6B2)

This method for total soil OC involves production, purification and measurement of CO2 evolved when soil carbon is ignited in a stream of O2. Because all C compounds are converted to CO2, the C from carbonates, charcoal, undecomposed wood, etc, will be included, as no soil pre-treatment is specified. In the volumetric sub-method 6B2a, concentrated KOH solution is used to absorb the CO2 released. The difference between the original volume of gas in the burette and the volume produced after ignition equals the volume of CO2 evolved from the sample, after correction for gas temperature and pressure. Sub-method 6B2b is similar to Method 6B2a, except the CO2 produced by ignition is measured via infrared / thermal conductivity detection. Both 6B2a and 6B2b use finely-milled air-dry sample, with weights varying with expected C concentrations. Surrogate estimates can be obtained by NIR (method 6B4a) or MIR (method 6B4b) reflectance spectroscopy. The methods specify reporting as %C on an oven-dry (105oC) basis.

Close

Total soil N – Dumas high-temperature combustion (7A5)

This method utilises automated and/or microprocessor controlled instrumentation, which mostly is able to measure at least total C, N and S in the same sample. Dumas-N dry oxidation includes all forms of soil N, without the need for lengthy pre-treatments, although results can occasionally differ from those expected in soils with high levels of fixed ammonium-N (lower results) and when soils are organically rich (high results, due to incomplete combustion resulting in the formation of methane rather than CO2). Typically, dry, finely-ground sample is subjected to high-temperature combustion (e.g. 950–1,250oC) in a stream of purified O2. An aliquot of the gases produced by combustion is carried by helium gas to a thermal conductivity cell for measurement of any N2 generated, a process typically taking 3–5 min. A heated copper catalyst reduces NOx to N2. The method specifies reporting results as %N on an oven-dry (105oC) basis.
Close

Not Specified or mixed (NS)

The laboratory either did not specify the method used or uses a mix of methods when submitting to the certification body

Close

GI-23

Wet digestion - open system without HF, and final medium HNO3/peroxide.  ICP-AES finish.

Close

CA-37

Finely divided dry sample.  Dumas combustion.