Close

Air dry moisture content (2A1)

This method is required to adjust soil chemical results based on air-dry samples to an oven-dry (105oC)
basis. When the air-dry moisture content (M%) is known, the correction from air-dry
to oven-dry is as follows:

 

            Oven-dry result  =   [Air-dry result  x  (100+ M%)]/100

Close

CaCl2 extractable B - ICP (12C2)

The soil is extracted with boiling 0.01M Cacl2 solution at a 1:2 soil:solution ratio for 10 mins.  It is then quickly filtered to avoid any re-fixation of the solubilised B.  The extract is then analysed by ICP-AES.

Close

Bicarbonate Extractable Phosphorus - Colwell (9B1)

This popular Australian P test on milled air-dry sample is suitable for acidic, neutral and alkaline soils. The extractant is freshly prepared 0.5M sodium bicarbonate @ pH 8.5. The wide soil/extractant ratio of 1:100 and an extended shaking time of 16 h favours readily available and more slowly available forms of soil P, while suppressing the solubility of basic calcium phosphates often found in neutral and alkaline soils. Method 9B1 describes a manual, molybdenum-blue colorimetric procedure with a preferred absorbance at 882 nm, whereas Method 9B2 refers to the same initial soil extraction, followed by an equivalent automated molybdenum-blue colorimetric finish (continuous segmented flow or flow injection analysis). The methods specify reporting results as mg P/kg on an air-dry basis.

Close

Electrical conductivity (EC) of 1:5 soil/water extract (3A1)

This test on milled air-dry sample at a soil/water ratio of 1:5 for 1 h is suitable for use on all soils, irrespective of whether acidic or alkaline. It usually underestimates the soluble salt status of soils containing natural or added gypsum, particularly if ³ 1% of gypsum is present. Such soils would have an EC of about 2 dS/m. Soil EC x 0.336 (Method 3B1) approximates percent total soluble salts, while approximate soil ionic strength (Method 3C1) at 0.1 bar (I0.1) can be calculated as follows: I0.1 = [0.0446*EC1:5 – 0.000173], where I0.1 has units of mM, and EC1:5 has units of dS/m @ 25oC.

Close

Exchangeable Acidity (15G1)

 

Exchange acidity (hydrogen and aluminium) by 1M potassium chloride

 
This is a preferred method for estimating the acidic cation status of acidic sub-tropical and tropical soils.

 

Close

Exchangeable Bases - Ammonium Chloride (15A1)

Method for measuring exchangeable bases (Ca2+, Mg2+, Na+, K+) - 1M ammonium chloride at pH 7.0

 

Suited for use on all soils, irrespective of whether acidic or alkaline, but preferred on acidic to weakly alkaline soils not dominated by solid-phase carbonates. Method 15A1 has no pre-treatment to remove soluble salts, with alternatives to remove them chemically (15A2) or to adjust for the presence of soluble sodium (15A3).

Close

KCl-ext.S (10D1)

Empirical extraction at 40oC in 0.25M KCl, for 3 hours.  Total S in the extract is measured by ICP-AES.

Close

pH: 1:5 SOIL:0.01M CaCL2 Suspension (4B2)

This pH test on milled air-dry sample is suitable for use on all soils, irrespective of whether acidic or alkaline. Values are usually unaffected by fertilisation prior to sampling, as changes to the soil’s ionic strength is masked by the calcium chloride. Code 4B1 indicates direct use of 0.01M CaCl2, at a soil/solution ratio of 1:5, with mechanical shaking for 1 h prior to pH measurement using calibrated electrodes positioned in the unstirred supernatant after settling of the suspension. Code 4B2 provides a similar measurement outcome but relies on the addition of 0.21M CaCl2 to a 1:5 soil/water suspension to achieve 0.01M CaCl2 prior to measurement of pH as for 4B1.

Codes 4B3 and 4B4 are identical to 4B1 and 4B2, respectively, except the soil/CaCl2 suspensions are stirred during measurement. Method 4B5 codes for an MIR surrogate measurement. There is merit in separate use of both water and calcium chloride to measure soil pH.

Close

pH of 1:5 soil/water suspension (4A1)

This test on milled air-dry sample involves mechanical shaking with deionised water in a closed system for 1 h at a soil/water ratio of 1:5 prior to pH measurement using calibrated electrodes, while stirring the soil/water suspension. The method is suitable for use on all soils, irrespective of whether acidic or alkaline. Values may be lower than expected on recently fertilised soils due to a temporary increase in soil solution ionic strength.
Close

Total organic carbon - high frequency induction furnace, volumetric (6B2)

This method for total soil OC involves production, purification and measurement of CO2 evolved when soil carbon is ignited in a stream of O2. Because all C compounds are converted to CO2, the C from carbonates, charcoal, undecomposed wood, etc, will be included, as no soil pre-treatment is specified. In the volumetric sub-method 6B2a, concentrated KOH solution is used to absorb the CO2 released. The difference between the original volume of gas in the burette and the volume produced after ignition equals the volume of CO2 evolved from the sample, after correction for gas temperature and pressure. Sub-method 6B2b is similar to Method 6B2a, except the CO2 produced by ignition is measured via infrared / thermal conductivity detection. Both 6B2a and 6B2b use finely-milled air-dry sample, with weights varying with expected C concentrations. Surrogate estimates can be obtained by NIR (method 6B4a) or MIR (method 6B4b) reflectance spectroscopy. The methods specify reporting as %C on an oven-dry (105oC) basis.

Close

Total soil N – Dumas high-temperature combustion (7A5)

This method utilises automated and/or microprocessor controlled instrumentation, which mostly is able to measure at least total C, N and S in the same sample. Dumas-N dry oxidation includes all forms of soil N, without the need for lengthy pre-treatments, although results can occasionally differ from those expected in soils with high levels of fixed ammonium-N (lower results) and when soils are organically rich (high results, due to incomplete combustion resulting in the formation of methane rather than CO2). Typically, dry, finely-ground sample is subjected to high-temperature combustion (e.g. 950–1,250oC) in a stream of purified O2. An aliquot of the gases produced by combustion is carried by helium gas to a thermal conductivity cell for measurement of any N2 generated, a process typically taking 3–5 min. A heated copper catalyst reduces NOx to N2. The method specifies reporting results as %N on an oven-dry (105oC) basis.
Close

Not Specified or mixed (NS)

The laboratory either did not specify the method used or uses a mix of methods when submitting to the certification body

Close

DE-23

Microwave Digestion - closed system without HF, and final medium HNO3 and/or HCl. ICP-AES finish.

Close

CA-37

Finely divided dry sample.  Dumas combustion.