Electrical conductivity (EC) of 1:5 soil/water extract (3A1)
This test on milled air-dry sample at a soil/water ratio of 1:5 for 1 h is suitable for use on all soils, irrespective of whether acidic or alkaline. It usually underestimates the soluble salt status of soils containing natural or added gypsum, particularly if ³ 1% of gypsum is present. Such soils would have an EC of about 2 dS/m. Soil EC x 0.336 (Method 3B1) approximates percent total soluble salts, while approximate soil ionic strength (Method 3C1) at 0.1 bar (I0.1) can be calculated as follows: I0.1 = [0.0446*EC1:5 – 0.000173], where I0.1 has units of mM, and EC1:5 has units of dS/m @ 25oC.
Exchangeable Bases - Ammonium Chloride (15A1)
Method for measuring exchangeable bases (Ca2+, Mg2+, Na+, K+) - 1M ammonium chloride at pH 7.0
Suited for use on all soils, irrespective of whether acidic or alkaline, but preferred on acidic to weakly alkaline soils not dominated by solid-phase carbonates. Method 15A1 has no pre-treatment to remove soluble salts, with alternatives to remove them chemically (15A2) or to adjust for the presence of soluble sodium (15A3).
DTPA Trace Elements (12A1)
Soils are extracted with 0.005M DTPA, at a 1:2 soil:solution ratio, and shaken for 2 hr at 25oC. Analytical finish is either ICP-AES or Flame AAS.
Ca(H2PO4)2 extractable S (10B3)
Sulfate sulphur is extracted in the absence of activated charcoal from air-dry soil <2 mm particle size, by 0.01M Ca (H2PO4)2 at pH 4.0 using a soil/solution ratio of 1:5 and an extraction time of 17 h at 25 degrees C. This extracted sulphur is then determined in an aliquot of particle-free soil extract by ICP-AES.
Mehlich3 ICP (18F1)
Analysis of Mehlich 3 extract using inductively-coupled atomic emission spectroscopy (ICP-AES)
pH of 1:5 soil/water suspension (4A1)
This test on milled air-dry sample involves mechanical shaking with deionised water in a closed system for 1 h at a soil/water ratio of 1:5 prior to pH measurement using calibrated electrodes, while stirring the soil/water suspension. The method is suitable for use on all soils, irrespective of whether acidic or alkaline. Values may be lower than expected on recently fertilised soils due to a temporary increase in soil solution ionic strength.Total organic carbon - high frequency induction furnace, volumetric (6B2)
This method for total soil OC involves production, purification and measurement of CO2 evolved when soil carbon is ignited in a stream of O2. Because all C compounds are converted to CO2, the C from carbonates, charcoal, undecomposed wood, etc, will be included, as no soil pre-treatment is specified. In the volumetric sub-method 6B2a, concentrated KOH solution is used to absorb the CO2 released. The difference between the original volume of gas in the burette and the volume produced after ignition equals the volume of CO2 evolved from the sample, after correction for gas temperature and pressure. Sub-method 6B2b is similar to Method 6B2a, except the CO2 produced by ignition is measured via infrared / thermal conductivity detection. Both 6B2a and 6B2b use finely-milled air-dry sample, with weights varying with expected C concentrations. Surrogate estimates can be obtained by NIR (method 6B4a) or MIR (method 6B4b) reflectance spectroscopy. The methods specify reporting as %C on an oven-dry (105oC) basis.