Analytes Certified for in 2022
This method is required to adjust soil chemical results based on air-dry samples to an oven-dry (105oC)
basis. When the air-dry moisture content (M%) is known, the correction from air-dry
to oven-dry is as follows:
Oven-dry result = [Air-dry result x (100+ M%)]/100
Initially, milled air-dry soil is extracted for 1 h with 2M KCl at a 1:10 soil/solution ratio. For 7C1a to 7C1h methods, mineral-N components are quantified by steam distillations and subsequent titrations. For 7C2 methods, mineral-N fractions in the clarified soil extract are determined by automated colorimetric procedures. Ammonium ions (NH4+) are measured by a modified Berthelot indophenol reaction, while the Griess-Ilosvay reaction is used for NO3-N (and NO2-N). The methods specify reporting results for NH4-N and NO3-N [plus NO2-N if present], respectively, as mg N/kg on an oven-dry (105oC) basis. Specifically, method 7C2a relates to an automated colour, continuous segmented flow analytical finish, while Method 7C2b codes an automated colour finish by flow injection analysis. Little difference is expected in results due to choice of colorimetric finish.
This test on milled air-dry sample at a soil/water ratio of 1:5 for 1 h is suitable for use on all soils, irrespective of whether acidic or alkaline. It usually underestimates the soluble salt status of soils containing natural or added gypsum, particularly if ³ 1% of gypsum is present. Such soils would have an EC of about 2 dS/m. Soil EC x 0.336 (Method 3B1) approximates percent total soluble salts, while approximate soil ionic strength (Method 3C1) at 0.1 bar (I0.1) can be calculated as follows: I0.1 = [0.0446*EC1:5 – 0.000173], where I0.1 has units of mM, and EC1:5 has units of dS/m @ 25oC.
Exchangeable bases - 1M ammonium acetate at pH 7.0.
This rapid method for exchangeable cations in non-saline acidic through to slightly alkaline soils has no pre-treatment for soluble salts. It should yield similar data to those of method 15A1, except it can overestimate exchangeable Ca in soils containing calcium carbonate.
This pH test on milled air-dry sample is suitable for use on all soils, irrespective of whether acidic or alkaline. Values are usually unaffected by fertilisation prior to sampling, as changes to the soil’s ionic strength is masked by the calcium chloride. Code 4B1 indicates direct use of 0.01M CaCl2, at a soil/solution ratio of 1:5, with mechanical shaking for 1 h prior to pH measurement using calibrated electrodes positioned in the unstirred supernatant after settling of the suspension. Code 4B2 provides a similar measurement outcome but relies on the addition of 0.21M CaCl2 to a 1:5 soil/water suspension to achieve 0.01M CaCl2 prior to measurement of pH as for 4B1.
Codes 4B3 and 4B4 are identical to 4B1 and 4B2, respectively, except the soil/CaCl2 suspensions are stirred during measurement. Method 4B5 codes for an MIR surrogate measurement. There is merit in separate use of both water and calcium chloride to measure soil pH.
Method 7A2 is similar to Method 7A1, except that total N in the Kjeldahl digest is quantified by automated colorimetric procedures based on the Berthelot indophenol reaction. Method 7A2a relates to an automated colour, continuous segmented flow analytical finish, while Method 7A2b codes an automated colour finish by flow injection analysis. No significant difference is expected in results due to the choice of colorimetric finish. The test commence with finely-milled air-dry sample, while both methods specify reporting results as %N on an oven-dry (105oC) basis.
The laboratory either did not specify the method used or uses a mix of methods when submitting to the certification body
Finely divided dry sample. Dumas combustion.
Wet digestion - open system without HF, and final medium H2SO4 (includes Kjeldahl - quantitative for NO3). Spectrophotometry (automated) finish.