Close

CaCl2 extractable B - ICP (12C2)

The soil is extracted with boiling 0.01M Cacl2 solution at a 1:2 soil:solution ratio for 10 mins.  It is then quickly filtered to avoid any re-fixation of the solubilised B.  The extract is then analysed by ICP-AES.

Close

Electrical conductivity (EC) of 1:5 soil/water extract (3A1)

This test on milled air-dry sample at a soil/water ratio of 1:5 for 1 h is suitable for use on all soils, irrespective of whether acidic or alkaline. It usually underestimates the soluble salt status of soils containing natural or added gypsum, particularly if ³ 1% of gypsum is present. Such soils would have an EC of about 2 dS/m. Soil EC x 0.336 (Method 3B1) approximates percent total soluble salts, while approximate soil ionic strength (Method 3C1) at 0.1 bar (I0.1) can be calculated as follows: I0.1 = [0.0446*EC1:5 – 0.000173], where I0.1 has units of mM, and EC1:5 has units of dS/m @ 25oC.

Close

Exchangeable Bases - Ammonium Chloride (15A1)

Method for measuring exchangeable bases (Ca2+, Mg2+, Na+, K+) - 1M ammonium chloride at pH 7.0

 

Suited for use on all soils, irrespective of whether acidic or alkaline, but preferred on acidic to weakly alkaline soils not dominated by solid-phase carbonates. Method 15A1 has no pre-treatment to remove soluble salts, with alternatives to remove them chemically (15A2) or to adjust for the presence of soluble sodium (15A3).

Close

DTPA Trace Elements (12A1)

Soils are extracted with 0.005M DTPA, at a 1:2 soil:solution ratio, and shaken for 2 hr at 25oC.  Analytical finish is either ICP-AES or Flame AAS.

Close

Colwell extractable K (18A1)

The Colwell extraction was developed for measuring available P, but can also be used for determining available K. The extractant is freshly prepared 0.5M sodium bicarbonate @ pH 8.5, with a soil:extractant ratio of 1:100 and a shaking time of 16 hr.  The sodium cation is considered the primary extractor, displacing the similar potassium cation from exchange sites.

Close

KCl-ext.S (10D1)

Empirical extraction at 40oC in 0.25M KCl, for 3 hours.  Total S in the extract is measured by ICP-AES.

Close

Nitrate Nitrogen (7C2)

Initially, milled air-dry soil is extracted for 1 h with 2M KCl at a 1:10 soil/solution ratio. For 7C1a to 7C1h methods, mineral-N components are quantified by steam distillations and subsequent titrations. For 7C2 methods, mineral-N fractions in the clarified soil extract are determined by automated colorimetric procedures. Ammonium ions (NH4+) are measured by a modified Berthelot indophenol reaction, while the Griess-Ilosvay reaction is used for NO3-N (and NO2-N). The methods specify reporting results for NH4-N and NO3-N [plus NO2-N if present], respectively, as mg N/kg on an oven-dry (105oC) basis. Specifically, method 7C2a relates to an automated colour, continuous segmented flow analytical finish, while Method 7C2b codes an automated colour finish by flow injection analysis. Little difference is expected in results due to choice of colorimetric finish.

Close

Phosphorus buffer index, with Colwell P (PBI+ColP) pooled analytical finishes (9I2A)

This index of soil P sorption embraces adsorption as well as precipitation reactions. In addition, it utilises the Colwell-P test on the same soil sample as a measure of current soil P fertility (PBI+ColP). Equilibrium soil extracts are obtained by shaking milled air-dry soil continuously for 17 h at a ratio of 1:10 (w/v) with a P equilibrating solution initially containing the equivalent of 1000 mg P/kg in 0.01M CaCl2. In method 9I2a, orthophosphate-P in final particulate-free supernatant solutions is analysed by a molybdenum-blue analytical finish, at a preferred absorbance of 882 nm. Methods 9I2b and 9I2c code for analytical finishes based on ICPAES and a vanadate-P colour finish, respectively. PBI+ColP is calculated as {[Ps (mg P/kg) + Colwell-P (mg/kg)] / c (mg P/L)0.41}, where Ps = freshly sorbed P and c = final solution P concentration. The methods specify reporting results on an air-dry basis.
Close

pH: 1:5 SOIL:0.01M CaCL2 Suspension (4B1)

This pH test on milled air-dry sample is suitable for use on all soils, irrespective of whether acidic or alkaline. Values are usually unaffected by fertilisation prior to sampling, as changes to the soil’s ionic strength is masked by the calcium chloride. Code 4B1 indicates direct use of 0.01M CaCl2, at a soil/solution ratio of 1:5, with mechanical shaking for 1 h prior to pH measurement using calibrated electrodes positioned in the unstirred supernatant after settling of the suspension. Code 4B2 provides a similar measurement outcome but relies on the addition of 0.21M CaCl2 to a 1:5 soil/water suspension to achieve 0.01M CaCl2 prior to measurement of pH as for 4B1. Codes 4B3 and 4B4 are identical to 4B1 and 4B2, respectively, except the soil/CaCl2 suspensions are stirred during measurement. Method 4B5 codes for an MIR surrogate measurement. There is merit in separate use of both water and calcium chloride to measure soil pH.

Close

pH of 1:5 soil/water suspension (4A1)

This test on milled air-dry sample involves mechanical shaking with deionised water in a closed system for 1 h at a soil/water ratio of 1:5 prior to pH measurement using calibrated electrodes, while stirring the soil/water suspension. The method is suitable for use on all soils, irrespective of whether acidic or alkaline. Values may be lower than expected on recently fertilised soils due to a temporary increase in soil solution ionic strength.
Close

Chloride - 1:5 soil/water extract (5A1)

Tests for water-soluble chloride (Cl) on milled air-dry sample are suitable for use on all soils. For method 5A1, Cl‑ in clarified 1:5 soil/water extracts is determined by potentiometric titration with AgNO3 in conjunction with an Ag/AgNO3 electrode array. For method 5A2a, Cl‑ in clarified 1:5 soil/water extracts is determined by an automated, continuous flow colorimetric procedure based on the formation — in the presence of ferric ions and free thiocyanate ions — of highly coloured ferric thiocyanate in proportion to the Cl‑ concentration. Method 5A2b is similar, except it pertains to the use of flow injection analysis (FIA). For 5A1 and 5A2 methods, it is assumed there are no chemical interferences of significance. Moreover, Method 5A2a has proven more precise than method 5A1, particularly at soil concentrations <50 mg Cl/kg. Other analytical finish options involve chemically-suppressed ion chromatography (5A3a), single-column electronically suppressed ion chromatography (5A3b), and direct measurement by ICPAES (Method 5A4). The methodology specifies reporting results on an air-dry basis.

Close

GG-23

Wet digestion - open system without HF, and final medium HNO3 and/or HCl.  ICP-AES finish.

Close

BA-32

Extraction with acid(s).  Titrimetric finish.

Close

BA-31

Extraction with acid(s).  Spectrophotmetry (automated) finish.

Close

CA-37

Finely divided dry sample.  Dumas combustion.